High-Quality Ceramic Alumina Tiles Lined Pipes for Mining Applications
The wear-resistant ceramic composite pipes and elbows produced by our company are in the form of dried shrimp joint welded elbows. The ceramic part is designed by the arching principle. The ceramic block forms a 360-degree mechanical self-supporting structure. The ceramic block is close to the inner wall of the steel pipe. The contact surface edge of all ceramic blocks adopts a tapered design. The blocks are interlocked to ensure that the blocks will not Fall off.
The gap between the porcelain block and the inner wall of the steel pipe is filled with high-temperature wear-resistant cement, and the elbow can withstand the greater impact generated by the material and use it under higher temperature conditions.
Features:
1. Wear resistance and service life
The selected alumina ceramic material has high hardness and good wear resistance. The wear resistance of the arched alumina ceramic elbows is 7 times that of stainless steel and 6 times that of cast steel. Its impact and wear resistance is equivalent to stainless steel, but it is significantly better than carbon steel, about 1.2 times that of cast steel, far better than cast stone, impact resistance is 8-16 times that of cast stone, and its weight is only wear-resistant alloy steel Half of it. One-third of the cast stone pipe.
2. Easy to install
3. Reasonable structure
The arched structure form 360 degrees, each porcelain plate is mutually squeezed and self-locking installation is more firm, the porcelain plate and the steel pipe are bonded and filled with high-temperature wear-resistant cement, which has better impact resistance and high-temperature resistance.
4. Low running resistance
The inner surface is smooth and never corroded, unlike the convex spiral on the inner surface of the seamless steel pipe. The smoothness of its inner surface is better than that of any metal pipe and slightly lower than that of a seamless pipe. Therefore, it has the characteristics of low running resistance, which can reduce operating costs.
5. Corrosion resistance, anti-scaling
a-AL2O3 is a neutral character and belongs to a substance that has been oxidized. Therefore, it has acid and alkali resistance and seawater corrosion resistance and also has anti-scaling properties.
Tile Specification
Character |
92 |
95 |
T95 |
99 |
ZTA |
ZrO2 |
Density(g/cm³) |
≥3.6 |
≥3.65 |
≥3.7 |
≥3.83 |
≥4.15 |
≥5.9 |
Al2O3(%) |
≥92% |
≥95% |
≥95% |
≥99% |
≥75% |
/ |
ZrO2 +Y2O3 |
/ |
/ |
/ |
/ |
≥21% |
≥99.8% |
Bending Strength(MPa) |
≥220 |
≥250 |
≥300 |
≥330 |
≥400 |
≥800 |
Compressive Strength (MPa) |
≥1050 |
≥1300 |
≥1600 |
≥1800 |
≥2000 |
/ |
Fracture Toughness(MPa.m1/2) |
≥3.2 |
≥3.2 |
≥3.5 |
≥3.5 |
≥5.0 |
≥7.0 |
Rockwell Hardness HRA |
≥82 |
≥85 |
≥88 |
≥89 |
≥90 |
≥88 |
Vickers Hardness HV20(MPa) |
≥950 |
≥1000 |
≥1100 |
≥1200 |
≥1400 |
≥1100 |
Wear Volume(cm³) |
≤0.25 |
≤0.20 |
≤0.15 |
≤0.10 |
≤0.05 |
≤0.05 |
Our Company :
Zibo Qimingxing New Material Incorporated Co.,Ltd
1.Established in 1997,25 years experience in wear solutions products.
2.Factory is under expanding, the total construction area is 50,000 sqm.
3.ISO9001:2015 certified,over 400 staffs.
4.Three Own-designed production lines, the ball mils are own produced.
QMX provides wear resistant solutions to all industries including Mining, Mineral , Base & Precious Metal Smelting, Power Generation (coal fired power stations), Iron and Steel, Cement & Lime Manufacture, and Petro-Chemical Refining and Production.
The company specializes in the production of HC series wear-resistant ceramic liners(alumina ball, zirconium silicate ball, zirconia toughed alumina ball, zirconium ball), agate ball, polyurethane ball, 92/T95/ZTA wear-resistant ceramic liner (alumina liner, zirconium toughed aluminum composite liner, zirconia plate), three-in-one, Two-in-one vulcanized ceramic runner sheet, ceramic mending compound, ceramic lining cyclone, ceramic lining pipe.
Packing And Shipping
1. Packaged with carton box.
2. There are compartments in the cartons to prevent friction.
About package and shipping marks all could be customized.
FAQ :
Q: Are you a trading company or manufacturer?
A: We are manufacture for 25 years.
Q: Is the sample free?
A: Yes, we offer free samples.
Q: How long is your delivery time?
A: Generally it is 1-2 days if the goods are in stock. or it is 15-30 days if the goods are not in stock, it is according to quantity.
Q: What are your terms of payment?
A: 30% T/T in advance, balance before shipment.
Q: Accept customized?
A: Yes. Kindly send all your details to our work.