Wearing Compound Small Ceramic Beads Filled Epoxy Resin for Mine Quick Maintance

Product Description

Small Ceramic Beads filled Epoxy Resin For Mine quick maintance

 

Product Parameters

 

Item	Index
Color	Grey(White Grain)
Density(g/cm3)	2.0
Weight Ratio(A:B)	2:1
Operating time(min)	10~30(can be customized)
Minimum curing time(min)	30
Full curing time(h)	4
Hardness after solidify(Shore D)	100.0
Compressive strength(Mpa)	111.0
Shear strength(Mpa)	32
Working temperature(ºC)	-20~80(Customized for high temperature)

Product Description

Qimingxing's wearing compounds are unique patented epoxy resin systems containing diamond hard ceramic beads that resist sliding abrasion. Directions for use-surface preparataion: Proper surface preparation is critical to the long termm performance of this product.The exact requirements vary with the severity of the application,expected service life, and initial substrate conditions. 1.On all vertical r overhaed applications,tacking welding expanded metal mesh onto the metal substrate is strongly reconnended prior to application of Wearing Compound. 2.Clean,dry,and abrade application surface.The more torough the degree of surface preparation, the better the performance of the application.If possbible,it is recommended that the surface be grit blasted to a Near White Metal(SSPC-SP10/NACE No.2)Standard.For less severe applications,roughening the sureface with hand tools is suirtable. Mixing:

1.Measure 2 parts resin to 1 part hardener by volume or weight on a clean and dry mixing surface and mix together until iniform in color.(If resin and hardener temperatures are 15ºC/60ºF or below,prehead resin only to about 21ºC/90ºF but not to exceed 37ºC/100ºF) 2.Immediately after abrasive blasting,rub a thin layer of material onto the surface to "wet" for good adhesion.) Operation:

1.Apply filly mixed material to the prepared surface. 2.Initially apply the material in a very thin layer to "wet" out the surface and avoid air entrapment. 3.At 25ºC/77ºF,the working time is 30 minutes.Working and solidify time depend on temperature and mass;the higher the temperature,the larger the mass , the faster the solidifying. 4.Functional cure time is 7 houra at 25ºC/77ºF. 5.Caution!Use approved,positive-pressure,supplied-air respirator when welding or torch cutting near cured compound. Use approved self-contained breathing apparatus when burning,welding,or torch cutting indoors near cured compund.Use approved respirator for dests and mists when grinding or machining cured compound. Do not use open flame on compound.See other cautions on Material Safety Data Sheet.
 

Company Profile

ZIBO QIMINGXING NEW MATERIAL is located in Zibo, Shandong,Near Qingdao port. With an excellent geographical location and a convenient logistics system,This enable us to provide you varies transportation modes (by express/air/sea) according to your needs. Also, ensure us OTD and save your shipping cost. Our 86700 m2 factory has obtained ISO 9001 and ISO 14001 certification and employs over 400 staff members who enable us to provide you with fully custom services upon request.

We accept customized designs, packing, logo or custom material. We can make custom design based on your inquiry. We provide NDA agreement to keep your design in private.
Our well-equipped facilities and excellent quality control throughout all stages of production enable us to guarantee your satisfaction.
Our business staff have 7~10 years of experience in the industry and can provide you with quality services. All your inquiries will be responded within 24 hours.

Ceramic wear tiles Series we can supply:
1. 92%,95%,T95%,99% Alumina ceramic tiles
2. ZTA(Zirconia Toughened Alumina) tiles/brick/block 
3. Ceramic Rubber and ceramic-Rubber-steel impact resistant liner
4. Monolihic Cyclone/ cyclone tiles/Ceramic Lined pipe fittings
5. High impact ceramic wearing compound 
 

 

FAQ

1. Are you are trading company or a factory? 
We are a leading factory, manufacturing high alumina ceramic wear resistant liners in Zibo, China 

2. What is your monthly capacity? 
800 ton per month 

3. What kinds of ceramic wear resistant liners do you manufacture? 
92%alumina liner, 95%alumina liner, T95%alumina liner, zirconia tile liner, ZTA tiles , ceramic-rubber composite plates, wearing compound 

4. What is the delivery time? 
If we have stock, the delivery time is within 3days after order confirmed. If there is no stock, it is usually 13days. 

5. Can you manufacture ceramic liner according to customers' desgin? 
Yes, we have 5 engineers and we can produce ceramic parts according to the drawings of the customers. 

6. What is the packing? 
carton, and then wooden pallet or wooden box, 20~25tons per 1*20"FCL 

7. What is the nearest port? 
Qingdao port